Software

Contents

1.Outline

[Attention]
This firmware is available from the Ver. 2.4 user. After completing the upgrade to Ver 2.4 certainly, proceed to upgrade to Ver. 2.5. When installing Vibration Analysis Program SX-A1VA, Ver.2.5 is required.

The followings are improved and upgraded.
・Vibration Analysis Program SX-A1VA is supported.
・Instruction manual is updated.
・NC-75 is added as the selectable calibrator. The sensitivity range when selecting the accelerometer is changed.

Version number:Version 2.5
Release date:November 7th, 2017

2.Download and Installation

[Attention]
This firmware is available from the Ver. 2.4 user. After completing the upgrade to Ver 2.4 certainly, proceed to upgrade to Ver. 2.5.

You will need:

・ RIONOTE unit attached amplifier unit SA-A1B4 or B2.
・ AC adaptor and also fully charged battery (with three battery power gauge displayed. ).
・ SD card
(Note: use a Rion approved SD memory card to guarantee performance.
For example: SX-A1RT and SX-A1FT
・ Downloaded firmware Version 1.01 (Updated firmware)

1. Unzip the downloaded file "SA-A1_Firmware_Ver_2_5.zip".
When you unzip, saa1_system_update_v2.5.zip,saa1_utility_update_v2.4.zip, saa1_app_ft_v2.4.zip, saa1_app_rt_v2.4.zip, saa1_app_wr_v2.4.zip saa1_ampunit_update_v2.4.zip will be created into the lowest hierarchy.

2. The folder hierarchy is shown below. Copy these files to the SD card (No need make a folder. Copy it to the root directory of the SD card.)

3. Procedure of each firmware upgrade are shown below:
To avoid running out of battery during the upgrade , mount fully charged battery (with three battery power gauges displayed.) and also connect the AC adapter before updating the program.

3.1 SA-A1 System Utility
Insert the SD card into the SA-A1and turn it on.
Tap [Program Manager] on the HOME screen, tap [System] and tap [Check SD Card].
1. The "Utility" Ver. 2.04 is displayed. Tap [Update].
2. The message asking for Update is displayed. Tap [Update].
3. When the update is complete, tap [Check SD memory card].
4. The “System” Ver. 2.05 is displayed. Tap [Update]
It takes several tens of minutes for completing the update of “System”.
Do not pull out the SD memory card during update of the system.



3.2 Waveform Recording Program SX-A1WR, 1/3 Octave Band Analysis Program SX-A1RT and FFT Analysis Program SX-A1FT
Insert the SD card into the SA-A1 and turn it on.
Tap [Program Manager] on the HOME screen, tap [Program] and tap [Check SD Card].
"SX-A1RT", "SX-A1FT", "SX-A1WR" and each version number 2.04 are displayed in [Install/update] column, and tap [Update].
A message to confirm update is displayed and tap [OK], Next, a message to confirm program update is displayed, and tap [Install].
Do not pull out the SD memory card during update of the system.
When the update is complete, the message is displayed and tap [Done].

3.3 Amplifier Unit SA-A1 B2/B4
Insert the SD card into the SA-A1 and turn it on.
Tap [Amplifier Unit Management] on the HOME screen.
Slide the screen down and tap [Run] in [Update].
The update screen is displayed and tap [OK].
Do not pull out the SD memory card during update of the system.

4. After the version update process is completed, verify that the version for SA-A1 System Utility, SX-A1RT, SX-A1FT, SX-A1WR and Amplifier Unit system are all 2.01.(only shows when they are installed) (The version of programs are displayed only when they are installed.)
The version of each program and system utility can be checked by accessing [Program] or [System] from the [Program Manager], Amplifier Unit can be checked by accessing [Amplifier Unit Management].
After you have verified that the update was performed correctly, the files used for version upgrade on the SD card will no longer be needed.

3.Software License Agreement

Do not agree
Agree to the above and download